Teltonika FM1010

Teltonika FM1010

Manufacturer:

4 out of 5 based on 2 customer ratings

Teltonika FM1010 is a vehicle telematics unit that easily plugs into a vehicle’s OBDII port of almost any car. It can’t read telemetry data from vehicle diagnostic system, but controls ignition status in various ways and detects harsh driving. The possible applications for FM1010 are Fleet and mobile workforce management, Usage Based Insurance, Car Rental, and Teenage driver tracking.

Teltonika FM1010 description

Teltonika FM1010 is a vehicle telematics unit that easily plugs into a vehicle’s OBDII port of almost any car. It’s the first OBDII tracker of Teltonika. It can’t read telemetry data from vehicle diagnostic system, but controls ignition status in various ways and detects harsh driving. The possible applications for FM1010 are Fleet and mobile workforce management, Usage Based Insurance, Car Rental, and Teenage driver tracking.

Package contents

When you open the cardboard box, you’ll see just Teltonika FM1010 device, supplied with a USB cable. If you use the tracking software that automatically configures the device, you’ll hardly need that cable. Otherwise you can use it for manual configuration from a PC, or for firmware upgrade.

Most commonly Teltonika FM1010 comes with built-in backup battery (Li-ion, 170 mAh), that’s already installed. However, if you are not sure, you’d rather check that yourself – you’ll need to open the casing.

Optional accessories you might require for special cases:

  • OBDII extension cable
  • OBDII adaptor

Location and tracking

FM1010 model is embedded with GPS chip and also it has the support of GLONASS. It doesn’t support Assisted GPS (A-GPS) technology, that’s why acquiring of the signal might take some more time, but normally it does not exceed a couple of minutes. As the back-up, when no satellites signals are available, it uses Cell ID location (also known as LBS-tracking).

The tracking mode can be flexible configured: by distance, time and turning. We’d recommend to use the following parameters: distance 100m, time 60 sec, and on turning on 30 degrees. When there is no movement (detected by “Ignition” status), tracker sends data in a specified time interval (i.e. 180 seconds). That’s quite convenient and useful for power saving.

OBDII data reading: none

Since Teltonika FM1010 is a basic tracker, it does not read any data from vehicle’s diagnostic system, such as dashboard speed, engine RPM, coolant temperature, MIL, DTC codes, etc. Instead it only gets power supply from OBDII port and can measure up the board voltage.

Mobile networks

Standard quad-band GSM module allows to use FM1010 in most of the regions covered with 2G GSM netwrorks. The slot for a SIM card (normal size) is located on the butt-end of the device. There is no any sensor for SIM card slot opening.

Power supply

FM1010 gets the power from OBD II Connector Type A. The voltage level must be in the range of 10-16V. Device also features a built-in rechargeable Li-ion backup battery with the capacity of 170mAh. When fully charged it ensures about one hour of device operation in normal conditions.

“Ignition” status

There is a virtual “Ignition” flag in FM1010, which is determined by either:

    • External power voltage – when the power level falls below a certain configured level (by default 10V), the “Ignition” is considered to be OFF, otherwise – ON.
    • Digital Input #1 – if there is positive signal on PIN #1 of the socket, the “Ignition” flag is ON. Important notice: on some cars it does not work.
    • Acceleration sensor – when the built-in accelerometer detects movement, the “Ignition” flag is ON.

“Stop/Movement” mode

Teltonika FM1010 determines whether vehicle is on move or stopped by one of three methods (configurable by user):

MethodMovingStopped
by Board Voltage If board voltage is above certain level (configurable, 10V by default)If board voltage is lower than a certain level
by AccelerationInternal accelerometer detects movementInternal accelerometer does not detect movement
by GNSSGNSS is fixed and speed is above 5 km/hGNSS is fixed and speed is below 5 km/h  or GNSS is not fixed

Two sleep modes

FM1010 is able to go to Sleep mode after configurable Sleep timeout. This timeout (defined period) starts counting when device is in STOP mode. After timeout is reached and all conditions for sleep mode are met, device goes to normal sleep or deep sleep mode:

  • Normal sleep mode. While in normal sleep mode, FM1010 turns GNSS module OFF, but keeps GSM module ON. The device is not making any new periodic GPS records, just monitoring the events with the last known coordinates and sends them to tracking server. As a result power consumption decreases allowing saving vehicle’s battery (below 2 mA).

FM1010 exists normal sleep mode when “Movement” mode detected or “Ignition” switches on.

  • Deep sleep mode. While in deep sleep mode, FM1010 sets both GNSS receiver and GSM/GPRS module to OFF state, thus making impossible to wake up the device remotely. Battery consumption drops below 2 mA.

FM1010 exits deep sleep mode if at least one of following conditions is true:

    • “Movement” mode is detected
    • “Ignition” is turned on
    • USB cable is connected

Driving behaviour monitoring

Teltonika FM1010 allows to monitor driving behaviour, making possible to use the device for insurance telematics. There are two configurable scenarios which designed for monitoring driving behaviour called Green Driving and Over Speeding.

Green Driving Scenario helps to inspect driver about harsh driving. Scenario continuously monitors: accelerating force, braking force and cornering angles. To prevent generating false events, harsh acceleration and harsh braking is monitored only when following conditions are fulfilled:

  • Ignition (Configured to be detected by Power Voltage, Ignition or Accelerometer) is turned on.
  • Vehicle speed is equal or higher than 10 km/h.

Harsh cornering is monitored only when following conditions are fulfilled:

  • Ignition (Configured to be detected by Power Voltage, Ignition or Accelerometer) is turned on.
  • Vehicle speed is equal or higher than 30km/h.

Over Speeding Scenario helps to prevent from exceeding fixed speed and inspects driver if needed.

Local and remote management

Unfortunately Teltonika FM1010 tracker can’t be controlled over GPRS, though it supports firmware updating via GPRS (FOTA). However, there is a wide list of SMS commands in a human-friendly format, on which device always replies back. In particular, Server and APN settings can be applied remotely with SMS. To decrease the amount of SMS required for configuration SMS in binary format can be also used – and the most advanced GPS tracking software platforms allow to utilise that.

Alternatively, you can configure FM1010 from a PC using proprietary software (Teltonika Configurator) and standard USB-cable which is included into package.

LED indication

FM1010 has two green LEDs located on the back panel, close to the SIM card slot. They are not very bright, and won’t blind the driver at night, but help to understand what’s the reason of the technical issue, when it occurs.

  • Status LED: indicates GSM/GPRS mode
  • Navigate LED: indicates GPS reception

Specifications and Features

Supported features

Server Integration
Server IP Address217.23.132.215
Server port47776
Integrated on15/11/2015
General information
PurposeVehicle
InstallationDIY
Special form factorOBDII Dongle
Housing
Weight100 g (3.53 oz.)
Size50.7x49.6x25 mm (2x1.95x0.98 in)
GNSS Location
Internal antenna (GNSS)
External antenna (GNSS)
GPS
GLONASS
Connectivity
Cellular network typeGSM Quad Band
Cellular network generation2G
Interfaces
Outputs
Hardware features
Battery capacity170 mAh
Built-in battery
Emergency button
Hardware extras
Fuel level sensor reading
Fuel temperature sensor reading
Tracking features
Tracking modesContinuous, Interval
Location by Cell IDFeature already supported
Feature already supported in
Smart power consumptionFeature already supported
Feature already supported in
ECO drivingFeature already supported
Feature already supported in
Events monitoring
Battery lowFeature already supported
Feature already supported in
Input change
Feature already supported in
Device switched on/offFeature already supported
Feature already supported in
Self monitoring
Network signal levelFeature already supported
Feature already supported in
GNSS signal levelFeature already supported
Feature already supported in
GNSS satellites fixedFeature already supported
Feature already supported in
External power source voltageFeature already supported
Feature already supported in
Internal battery levelFeature already supported
Feature already supported in
CAN/OBDII reading
CAN/OBDII reader type
Feature already supported in
DTC codes reading
Feature already supported in
Remote management
Server connection setup over SMSFeature already supported
Feature already supported in
Remote device configurationYes (over SMS)Feature already supported
Feature already supported in
Remote outputs controlYes (over SMS), Over GPRS (Requires firmware 00.06.XX)Feature already supported
Feature already supported in
Firmware update OTA
Feature already supported in
Certification
CE
Feature already supported in
FCC
Feature already supported in

Tracking software

Navixy

Server Integration
Server IP Address217.23.132.215
Server port47776
Integrated on15/11/2015

Other platforms

Teltonika devices are quite popular in the world. Not surprisingly they and integrated in many GPS tracking software platforms including GPSWOX, GPSGate, Wialon, GPS-Server and others. However, the level of integration may vary. For example, it’s rare to see that device is configured automatically: more commonly you will need to setup the device using Teltonika configuration software, e.g. manually enter APN settings, server address and port. Also, for example, not every platform supports advanced features like Green driving features, reading CANbus data or remote control of the outputs, monitoring device’s battery, signal strength, etc.

2 reviews for Teltonika FM1010

  1. Michael Hess
    3 out of 5

    :

    Average functionality. It’s not a real OBDII: it can’t read diagnostic parameters on ANY car.

  2. MILOŠ
    5 out of 5

    :

    teltonika fm1010 works quite well on most cars, with very, very rare exceptions. i wouldn’t agree that it’s “not a real obd2 tracker”. it does not read diagnostic data, but no one promised, right? it’s a basic model for vehicle tracking and should be handled respectively. i can say it works much better than many other obd trackers. it’s well assembled and has good gps reception. they only thing you should care is the motion sensor: in some cars pin #1 doesn’t work well and the device doesn’t wake up. i’d recommend always use the voltage based algorithm instead.

Add a review