STAB Liner 102

Manufacturer:

STAB Liner 102 is a GLONASS/GPS/GSM terminal designed to solve basic vehicle fleet management tasks: monitoring, mileage and fuel consumption control, voice communication with the driver, e.t.c.

STAB Liner 102 description

STAB Liner 102 is a GLONASS/GPS/GSM terminal designed to solve basic vehicle fleet management tasks: monitoring, mileage and fuel consumption control, voice communication with the driver, e.t.c.

The device combines optimal functionality and low cost, can be used on any vehicle, including light vehicles such as motorcycles, snowmobiles and scooters.

Location and tracking

  • GPS, GLONASS
  • Continuous tracking mode
  • no LBS support

Mobile networks

  • Bands: 850, 900, 1800, 1900 Mhz
  • 2G only

Power supply

  • Power supply 5.5 – 58V
  • Built-in 2000 mAh battery

Inputs and outputs

  • 4 universal inputs
  • 4 discrete inputs
  • 4 discrete outputs
  • RS-232 support
  • RS-485 support
  • CAN support

Other features

  • 2 SIM cards
  • Optional emergency button
  • Optional RFID reader

Specifications and Features

Supported features

Server Integration
Server IP Address217.23.132.215
Server port47698
General information
PurposeVehicle
InstallationDIY
Housing
Weight300 g (10.58 oz.)
Size40x140x120 mm (1.57x5.51x4.72 in)
GNSS Location
Internal antenna (GNSS)
GPS
GLONASS
Connectivity
Cellular network typeGSM Quad Band, GSM 850/900/1800/1900
Internal antenna (Connection)
Cellular network generation2G
Interfaces
1-Wire interface
RS232 interface
Number of RS232 interfaces1
RS485 interface
Number of outputs4
Number of inputs (all types)8
Discrete inputsFeature already supported
Feature already supported in
Analog inputsFeature can be supported upon request
Feature can be supported upon request
Impulse inputsFeature can be supported upon request
Feature can be supported upon request
Frequency inputsFeature can be supported upon request
Feature can be supported upon request
Hardware features
Emergency buttonOptionalFeature already supported
Feature already supported in
Hardware extras
Fuel level sensor readingFeature can be supported upon request
Feature can be supported upon request
Voice listeningFeature can be supported upon request
Feature can be supported upon request
Driver ID readingFeature can be supported upon request
Feature can be supported upon request
External temperature sensor readingFeature can be supported upon request
Feature can be supported upon request
CameraFeature can be supported upon request
Feature can be supported upon request
Tracking features
Tracking modesContinuous
Feature can be supported upon request
OdometerFeature already supported
Feature already supported in
Events monitoring
Battery lowFeature already supported
Feature already supported in
Self monitoring
Network operator IDFeature can be supported upon request
Feature can be supported upon request
GNSS signal levelFeature already supported
Feature already supported in
Internal battery levelFeature already supported
Feature already supported in
Remote management
Server connection setup over SMSFeature already supported
Feature already supported in
Remote device configurationYes (over GPRS)Feature already supported
Feature already supported in
Remote outputs control
Feature already supported in
Forced GNSS location update over SMSFeature already supported
Feature already supported in

Server software

Navixy

Server Integration
Server IP Address217.23.132.215
Server port47698

Automatic activation (recommended)

The software platform supports automatic device activation by applying APN settings, server address and port, as well as recommended tracking mode though the SMS channel. Normally you don’t need to configure anything manually. Just install the SIM card, switch the device ON and make sure it is located in the place with good GPS signal reception.

You also need to keep the device with initial factory settings, in particular:

  • Do not set any password, keep it clear (as by default)
  • Do not set any master number prior to the device activation
  • Do not set local Time zone, it must be UTC+0h (as by default)

Manual activation

In case automatic activation failed, you can try to register the device manually by sending following commands to the device:

APN=”{apn}”r
LOGIN=”{apn_user}”r
PASSWORD=”{apn_pass}”r
SERVER={server_ip}:47698r

The <APN> parameters depend on your GSM carrier.

Reviews

There are no reviews yet.

Be the first to review “STAB Liner 102”