Queclink GV500VC

Manufacturer:

Queclink GV500VC is a dual-band CDMA 2000 OBDII tracker that easily plugs into vehicle’s diagnostic port. Thanks to sensitive GNSS chip from u-blox, A-GPS technology and two GNSS antennas it provides accurate location and reliable tracking. The device supports all major OBDII protocols and delivers much of the information from vehicle’s diagnostic systems.

SKU: f8c12552a9ca.

Queclink GV500VC description

Location and tracking

GV500VC comes with modern GNSS chip from u-blox, which has high sensitivity and receives signals of GPS, GLONASS and other systems. Besides it supports Assisted GPS (A-GPS) technology for faster location acquiring. To provide even better sensitivity the device is embedded with two GPS antennas (for manufacture dates starting from December 2015). The second antenna serves as a backup in case the main antenna does not perform well in some specific situations (OBDII trackers are often placed under the wheel’s column where GPS signals are weaker). All of these give a positive impact on the quality of tracking.

As for the tracking modes, they are fully adjustable: by time and distance intervals, direction change. The device has power saving modes and well detects the movement status according to the Ignition stat (PIN #1) and smart proprietary algorithm based on internal G-Sensor.

Mobile network

Dual band CDMA2000 1xRTT frequencies 800/1900 MHz, 3G support.

OBDII diagnostic data

Queclink GV500VC reads a lot of data from an vehicle’s diagnostic system. The tracker supports many standards (J1850 PWM, J1850 VPW, ISO 9141-2, ISO 14230, ISO 15765, J1939, CAN_USER1, CAN_USER2 and VW TP2.0) and on this criterion is considered one of the best OBDII devices. With GV500VC you can retrieve the following information:

  • Fuel level
  • Fuel consumption
  • Dashboard speed
  • Coolant temperature
  • Throttle position
  • Engine load
  • VIN – Vehicle Identification Number
  • and other

It also provides information about MIL (Malfunction Indicator Lamp – Check Engine) and DTC error codes.

Events detection

The number of detected events far exceeds the typical amount for OBDII trackers. GV500VC hardware and firmware process such events as Tow, Harsh driving (braking, cornering, acceleration), Long idling (with engine working), Detach from OBDII socket, Low external power voltage, Low backup battery, Signal jamming and others.

Power supply

Advanced power management helps to provide lower power consumption and that device can work for many hours even in active mode.

Accessories

For specific installations an OBDII extension cable can be offered.

Specifications and Features

Supported features

Server Integration
Server IP Address217.23.132.215
Server port47764
Integrated on06/09/2013
Revised on19/02/2015
General information
PurposeVehicle
InstallationNot required
Housing
Weight42 g (1.48 oz.)
Size48x25x48 mm (1.89x0.98x1.89 in)
GNSS Location
Internal antenna (GNSS)
GPS
GLONASS
Galileo
Beidou
Assisted GPS
Chipsetu-blox
Connectivity
Cellular network typeCDMA2000 800/1900
Internal antenna (Connection)
Cellular network generation3G
Hardware features
Battery capacity130 mAh
Built-in battery
Accelerometer
Hardware extras
Fuel level sensor readingFeature already supported
Feature already supported in
Tracking features
Location by Cell IDFeature already supported
Feature already supported in
Smart power consumptionFeature already supported
Feature already supported in
OdometerFeature already supported
Feature already supported in
ECO drivingFeature already supported
Feature already supported in
Events monitoring
External power cut offFeature already supported
Feature already supported in
Car crashFeature already supported
Feature already supported in
TowingFeature already supported
Feature already supported in
Self monitoring
Network signal levelFeature already supported
Feature already supported in
GNSS signal levelFeature already supported
Feature already supported in
GNSS satellites fixedFeature already supported
Feature already supported in
Internal battery levelFeature already supported
Feature already supported in
CAN/OBDII reading
CAN/OBDII reader typeInternal, YesFeature already supported
Feature already supported in
CAN/OBDII parametersFuel level, fuel consumption, engine RPM, throttle position, speed, engine load, coolant temperature, DTC error codes and other, YesFeature already supported
Feature already supported in
DTC codes readingFeature already supported
Feature already supported in
Remote management
Server connection setup over SMSFeature already supported
Feature already supported in
Remote device configurationYes (over GPRS)Feature already supported
Feature already supported in
Forced LBS location update over GPRSFeature already supported
Feature already supported in
Forced GNSS location update over SMSFeature already supported
Feature already supported in

Tracking software

Navixy

Server Integration
Server IP Address217.23.132.215
Server port47764
Integrated on06/09/2013
Revised on19/02/2015

Automatic activation (recommended)

The software platform supports automatic device activation by applying APN settings, server address and port, as well as recommended tracking mode though the SMS channel. Normally you don’t need to configure anything manually. Just install the SIM card, switch the device ON and make sure it is located in the place with good GPS signal reception.

You also need to keep the device with initial factory settings, in particular:

  • Do not set any password, keep it clear (as by default)
  • Do not set any master number prior to the device activation
  • Do not set local Time zone, it must be UTC+0h (as by default)

Manual activation

In case automatic activation failed, you can try to register the device manually by sending following command to the device:

AT+GTQSS=gv500vc,{apn},{apn_user},{apn_pass},3,,2,{server_hostname},47764,,,+922 222 22,10,0,,,0001$

The <APN> parameters depend on your GSM carrier.

Reviews

There are no reviews yet.

Be the first to review “Queclink GV500VC”