Concox GT230

Manufacturer:

Concox GT230 device is a high-quality vehicle GPS tracker, which supports OBD reader. This tracker allows you to monitor wide list of vehicle parameters such as fuel consumption, water temperature, battery and voltage through the OBD interface in real time. It will help you not only to monitor the status of your vehicle in real time, but also to optimize your driving style. With built-in acceleration sensor the GT230 can remotely protect your vehicle from theft.

Concox GT230 description

Concox GT230 device is a high-quality vehicle GPS tracker, which supports OBD reader. This tracker allows you to monitor wide list of vehicle parameters. Also Concox GT230 has built-in acceleration sensor, which can remotely protect your vehicle from theft.

Location and tracking

  • GPS Support
  • Continuous tracking mode
  • LBS Support

Mobile networks

  • 850/900/1800/1900 MHz
  • 2G Network

Power supply

  • Build-in battery (400mAh)
  • External power supply (9-36 VDC)

Inputs and outputs

  • 1 Digital input

Other features

  • External emergency button support
  • Remote management
  • External CAN reader

Specifications and Features

Supported features

Server Integration
Server IP Address217.23.132.215
Server port47755
General information
PurposeVehicle
InstallationDIY
Housing
Weight50,5 g (17.81 oz.)
Size86.6x44.0x13.6 mm (3.41x1.73x0.54 in)
GNSS Location
Internal antenna (GNSS)
GPS
Connectivity
Cellular network typeGSM Quad Band
Internal antenna (Connection)
Cellular network generation2G
Interfaces
Number of inputs (all types)1
ACC/Ignition inputFeature already supported
Feature already supported in
Discrete inputsFeature already supported
Feature already supported in
Hardware features
Emergency buttonFeature already supported
Feature already supported in
Tracking features
Tracking modesContinuous
Feature already supported in
Location by Cell IDFeature already supported
Feature already supported in
Events monitoring
Battery lowFeature already supported
Feature already supported in
External power cut offFeature already supported
Feature already supported in
Self monitoring
Network signal levelFeature already supported
Feature already supported in
GNSS signal levelFeature already supported
Feature already supported in
External power source voltageFeature already supported
Feature already supported in
Internal battery levelFeature already supported
Feature already supported in
CAN/OBDII reading
CAN/OBDII reader typeExternalFeature already supported
Feature already supported in
CAN/OBDII parametersFuel level, fuel consumption, speed, engine RPM, throttle position, DTC error codes
Feature already supported in
Remote management
Server connection setup over SMSFeature already supported
Feature already supported in
Remote device configurationYes (over GPRS)Feature already supported
Feature already supported in
Forced GNSS location update over SMSFeature already supported
Feature already supported in

Server software

Navixy

Server Integration
Server IP Address217.23.132.215
Server port47755

Automatic activation (recommended)

The software platform supports automatic device activation by applying APN settings, server address and port, as well as recommended tracking mode though the SMS channel. Normally you don’t need to configure anything manually. Just install the SIM card, switch the device ON and make sure it is located in the place with good GPS signal reception.

You also need to keep the device with initial factory settings, in particular:

  • Do not set any password, keep it clear (as by default)
  • Do not set any master number prior to the device activation
  • Do not set local Time zone, it must be UTC+0h (as by default)

Manual activation

In case automatic activation failed, you can try to register the device manually by sending following commands to the device:

APN,<apn>,<apnUser>,<apnPass>#
SERVER,0,127.0.0.1,47755,0#
GPRSON,1#

The <APN> parameters depend on your GSM carrier.

Reviews

There are no reviews yet.

Be the first to review “Concox GT230”