CalAmp LMU-3640

Manufacturer:

CalAmp LMU-3640 is a next generation telematics gateway that includes a range of wireless and peripheral connectivity options and is equipped with CalAmp’s purpose built vehicle interface technologies for both light and heavy duty vehicles.

CalAmp LMU-3640 description

CalAmp LMU-3640 is a next generation telematics gateway that includes a range of wireless and peripheral connectivity options and is equipped with CalAmp’s purpose built vehicle interface technologies for both light and heavy duty vehicles.

Location and tracking

  • GPS/GLONASS Support
  • Continuous tracking mode
  • LBS Support

Mobile networks

  • 700/850/1700/1900 MHz
  • 3G / 4G Network

Power supply

Operating Voltage:

  • 9-30 VDC (Start-up, Operating)
  • 7-32 VDC (Momentary)

Power Consumption:

  • 7 mA @ 12V <500 uA (deep sleep)
  • 20 mA @ 12V (idle on network)
  • 150 mA @ 12V (active tracking with VBUS active)

Inputs and outputs

  • 5 Discrete input
  • 2 Analog input
  • 4 Digital outputs
  • 1-Wire Interface

Other features

  • Remote management
  • LED indication
  • Accessories

Specifications and Features

Supported features

Server Integration
Server IP Address217.23.132.215
Server port47710
General information
PurposeVehicle
InstallationProfessional
Housing
Weight142 g (5.01 oz.)
Size145x53x33 mm (5.71x2.09x1.3 in)
GNSS Location
Internal antenna (GNSS)
GPS
GLONASS
Galileo
Assisted GPS
Connectivity
Cellular network type1900/1700/850/700
Internal antenna (Connection)
Cellular network generation3G, 4G
Interfaces
1-Wire interfaceFeature already supported
Feature already supported in
RS232 interfaceFeature already supported
Feature already supported in
Number of RS232 interfaces1
Feature already supported in
Number of outputs4
Feature already supported in
Number of inputs (all types)7
Feature already supported in
ACC/Ignition inputFeature already supported
Feature already supported in
Discrete inputsFeature already supported
Feature already supported in
Analog inputsFeature already supported
Feature already supported in
OutputsFeature already supported
Feature already supported in
Tracking features
Tracking modesContinuous
Feature already supported in
Location by Cell IDFeature already supported
Feature already supported in
Self monitoring
Network signal levelFeature already supported
Feature already supported in
Network operator IDFeature already supported
Feature already supported in
GNSS signal levelFeature already supported
Feature already supported in
External power source voltageFeature already supported
Feature already supported in
CAN/OBDII reading
CAN/OBDII reader typeExternalFeature already supported
Feature already supported in
CAN/OBDII parametersSpeed, fuel level, fuel consumption, engine RPM, throttle position, mileage, inst. fuel consumption, engine hours
Feature already supported in
Remote management
Server connection setup over SMSFeature already supported
Feature already supported in
Remote device configurationYes (over GPRS)Feature already supported
Feature already supported in
Remote outputs controlYes (over GPRS)Feature already supported
Feature already supported in
Forced GNSS location update over SMSFeature already supported
Feature already supported in

Server software

Navixy

Server Integration
Server IP Address217.23.132.215
Server port47710

Automatic activation (recommended)

The software platform supports automatic device activation by applying APN settings, server address and port, as well as recommended tracking mode though the SMS channel. Normally you don’t need to configure anything manually. Just install the SIM card, switch the device ON and make sure it is located in the place with good GPS signal reception.

You also need to keep the device with initial factory settings, in particular:

  • Do not set any password, keep it clear (as by default)
  • Do not set any master number prior to the device activation
  • Do not set local Time zone, it must be UTC+0h (as by default)

Manual activation

In case automatic activation failed, you can try to register the device manually by sending following commands to the device:

!RP,2306,0,<apn>
!RP,2314,0,<apnUser>
!RP,2315,0,<apnPass>
!RP,1024,35,255,1
!RP,769,0,47710
!RP,2319,0,<server_ip>
!RP,768,0,<server_ip>
!RP,1024,25,255,2
!R3,70,0
!R3,1,123

The <APN> parameters depend on your GSM carrier.

Reviews

There are no reviews yet.

Be the first to review “CalAmp LMU-3640”