Bitrek BI 520 TREK

Manufacturer:

Bitrek 520 TREK is a device, which can be used for solving the problems of navigation, remote control and vehicle monitoring. This device is intended for installation on any object. Bitrek 520 TREK uses 2G Network, which is widely supported all over the world. Also tracker has a wide list of the inputs, which can be useful for the fleet monitoring. If GSM connection will be lost, 520 TREK will save all tracking points in the internal memory, as soon as device will establish connection again, tracking points will be uploaded to the server.

Bitrek BI 520 TREK description

Bitrek 520 TREK is a device, which can be used for solving the problems of navigation, remote control and vehicle monitoring. This device is intended for installation on any object. Bitrek 520 TREK uses 2G Network, which is widely supported all over the world. Also tracker has a wide list of the inputs, which can be useful for the fleet monitoring.
Location and tracking

  • GPS, GLONASS support
  • Interval tracking mode

Mobile networks

  • 900/1800 MHz
  • 2G Network

Power supply

  • Build-in battery
  • External power supply (6-36 V)

Inputs and outputs

  • 3 Digital inputs
  • 2 Analog inputs
  • 2 Outputs

Other features

  • 1-Wire
  • Remote management
  • IP54 Protection
  • Internal memory

Specifications and Features

Supported features

Server Integration
Server IP Address217.23.132.215
Server port47776
General information
PurposeVehicle
InstallationProfessional
Housing
Weight65 g (2.29 oz.)
Size96x60x14 mm (3.78x2.36x0.55 in)
GNSS Location
Internal antenna (GNSS)
GPS
GLONASS
Connectivity
Cellular network typeGSM 900/1800
Internal antenna (Connection)
Cellular network generation2G
Interfaces
1-Wire interface
Number of outputs2
Number of inputs (all types)5
ACC/Ignition inputFeature can be supported upon request
Feature can be supported upon request
Discrete inputsFeature already supported
Feature already supported in
Analog inputsFeature already supported
Feature already supported in
Impulse inputsFeature can be supported upon request
Feature can be supported upon request
Frequency inputsFeature already supported
Feature already supported in
Hardware features
Internal temperature sensorFeature already supported
Feature already supported in
Hardware extras
Fuel level sensor readingFeature already supported
Feature already supported in
Driver ID readingFeature already supported
Feature already supported in
External temperature sensor reading
Feature already supported in
Tracking features
Tracking modesInterval
Feature already supported in
OdometerFeature already supported
Feature already supported in
Self monitoring
Network operator IDFeature already supported
Feature already supported in
Network roaming statusFeature already supported
Feature already supported in
GNSS signal levelFeature already supported
Feature already supported in
External power source voltageFeature already supported
Feature already supported in
Internal battery levelFeature already supported
Feature already supported in
CAN/OBDII reading
CAN/OBDII reader typeExternalFeature already supported
Feature already supported in
Remote management
Server connection setup over SMSFeature already supported
Feature already supported in
Remote device configurationYes (over SMS)Feature already supported
Feature already supported in
Remote outputs controlYes (over SMS)Feature already supported
Feature already supported in

Server software

Navixy

Server Integration
Server IP Address217.23.132.215
Server port47776

Automatic activation (recommended)

The software platform supports automatic device activation by applying APN settings, server address and port, as well as recommended tracking mode though the SMS channel. Normally you don’t need to configure anything manually. Just install the SIM card, switch the device ON and make sure it is located in the place with good GPS signal reception.

You also need to keep the device with initial factory settings, in particular:

  • Do not set any password, keep it clear (as by default)
  • Do not set any master number prior to the device activation
  • Do not set local Time zone, it must be UTC+0h (as by default)

Manual activation

In case automatic activation failed, you can try to register the device manually by sending following commands to the device:

setparam 0245 {server_hostname};
setparam 0246 47776;
setparam 0242 {apn};
setparam 0243 {apn_user};
setparam 0244 {apn_pass};
setparam 0903 100;
setparam 0011 100;
setparam 0012 300;
setparam 0013 10;
setparam 0470 1;
setparam 0474 3;
setparam 0420 1;
setparam 0410 1;
setparam 0450 1;
setparam 0440 1;

The <APN> parameters depend on your GSM carrier.

Reviews

There are no reviews yet.

Be the first to review “Bitrek BI 520 TREK”